new beat productions  
This page holds all of our releases for the Atari series of computers. New releases will be found at the top of the page.

CT60 Remote
CT60 REMOTE Receiver board that when powered and hooked up to the CT60 allows you to reset, switch between 030/060 mode, and power-off your Falcon using the included remote.

A new batch has been produced and the CT60 Remote is available again. The CT60 reciever board is plug-and-play apart from the power cable that may have to be soldered to provide 5V and GND to the board. All cables needed are included in the package.

We currently have 3 of these left. No more will be produced once they are gone. Contact Daniel for more information.

Release date:
May 15, 2021
Hardware requirements:
Atari Falcon030
CT60, CT63 or CT63e

External Keyboard Adapter
EXTERNAL KEYBOARD ADAPTER Adapter that allows an external Atari Mega ST/STE or TT keyboard to be used with an Atari STFM/STE/Falcon030 computer.

Just add an RJ11 socket and a mechanical switch and you're good to go! The switch can be used to switch back and forth between the internal and external keyboard without opening up the case.

We currently have 4 of these left (including a mechanical switch and RJ11 socket if you don't have those). No more will be produced once they are gone. Contact Daniel for more information.

Release date:
May 4, 2021
Hardware requirements:
Atari ST/TT/Falcon030

It's that time of the year again
It's that time of the year again New Beat's contribution to the demo competition at Sommarhack 2020.

It was voted second best demo in the competition.

If you like the demo and want to show your appreciation, please consider giving it a thumbs-up at Pouet. Thanks!
Release date:
July 5, 2020
Sommarhack 2020
Hardware requirements:
Atari Falcon030
4Mb ST-RAM
VGA monitor
HDD or other mass storage
File information:
TIME.ZIP
4 765 kB
Downloads: 76

2.5" to 3.5" SCSI Adapter for the C-LAB Falcon
SCSI ADAPTER SCSI adapter that allows 3.5" devices (with 50-pin connectors), such as the CosmosEx, to be connected to the internal 40-pin SCSI cable of C-Lab Falcons. It will also work with an Atari Falcon030 with the internal SCSI modification done to it.

We currently have 1 of these left. No more will be produced once they are gone. Contact Daniel for more information.

Release date:
October 1, 2019
Hardware requirements:
C-LAB Falcon or Atari Falcon030 with the internal SCSI interface modification

Internal SCSI Terminator for the C-LAB Falcon
SCSI TERMINATOR Internal SCSI terminator for the C-LAB Falcon or Atari Falcon030 computers with the internal SCSI interface modification.

The internal SCSI terminator is needed if you have no internal SCSI device and want to connect one or more devices to the external SCSI port. The terminator plugs into the internal 40-pin ribbon cable for 2.5" SCSI devices.

Out of stock.

Release date:
September 30, 2019
Hardware requirements:
C-LAB Falcon or Atari Falcon030 with the internal SCSI interface modification

JOY
JOY JOY was New Beat's contribution to the demo competition at Sommarhack 2019 in Dalarna, Sweden.

It was voted best demo in the competition.

Version 1.1 of the demo, released on August 3, 2020, features compatibility with the 060 mode of CT6xx accelerated Falcons and a number of bugfixes. Version 1.1 is identical, both visually and audibly, to the version released at Sommarhack in July, 2019.

If you like the demo and want to show your appreciation, please consider giving it a thumbs-up at Pouet. Thanks!
Release date:
July 6, 2019
Sommarhack 2019
Version 1.1: August 3, 2020
Hardware requirements:
Atari Falcon030
4Mb ST-RAM
VGA or RGB monitor
HDD or other mass storage
File information:
JOY11.ZIP
8 122 kB
Downloads: 131

MORE
MORE MORE was New Beat's contribution to the demo competition at Sommarhack 2018 in Dalarna, Sweden.

It was voted best demo in the competition.

Version 1.1 of the demo, released on August 26, 2021, features compatibility with the 060 mode of CT6xx accelerated Falcons and a number of bugfixes. Version 1.1 is identical, both visually and audibly, to the version released at Sommarhack in July, 2018.

If you like the demo and want to show your appreciation, please consider giving it a thumbs-up at Pouet. Thanks!

Release date:
July 7, 2018
Sommarhack 2018
Version 1.1: August 26, 2021
Hardware requirements:
Atari Falcon030
4Mb ST-RAM
VGA or RGB monitor
HDD or other mass storage
File information:
MORE11.ZIP
8 716 kB
Downloads: 121

Nemesis Indicator v2.01
NIND Nemesis Indicator is a small memory resident program for Atari Falcon030 computers equipped with the Nemesis accelerator from Titan Designs or the Phantom accelerator from Phanatic. Nemesis Indicator displays the current Nemesis state (16/32 MHz, 20/24 MHz, 24/48 MHz) in the upper right corner of the screen and allows the state to be changed by a simple mouse click. Since version 1.1, the indicator graphics can be customized and a set of predefined indicators are included.

New in version 2.0 is a CPU power saver feature that, when enabled, will turn off the Nemesis after a specified number of minutes of no user activity. Whenever user activity is detected again, the most recent Nemesis state will be restored.

Version 2.0 also comes with a configuration CPX for the Atari XControl Panel, a larger selection of indicator graphics, and the complete source code (in assembly language and C).

Release date:
August 5, 2017
Hardware requirements:
Atari Falcon030
1Mb ST-RAM
VGA, RGB or mono. monitor
Nemesis or Phantom
File information:
NIND201.ZIP
52 kB
Downloads: 91
Total: 388 (all versions)

Love
LOVE This little intro for the Atari Falcon030 was New Beat's contribution to the demo competition at Sommarhack 2017 in Dalarna, Sweden.

It was voted sixth best demo in the competition.

If you like the demo and want to show your appreciation, please consider giving it a thumbs-up at Pouet. Thanks!
Release date:
July 13, 2017
Sommarhack 2017
Hardware requirements:
Atari Falcon030
1Mb ST-RAM
VGA monitor
File information:
LOVE.ZIP
36 kb
Downloads: 105

3-in-1 Monitor Adapter for the Atari Falcon030
3-IN-1 MONITOR ADAPTER The 3-in-1 monitor adapter is a small piece of hardware that plugs into the monitor port of the Atari Falcon030. Its main purpose it to make it possible to connect the Falcon030 to a monitor using a standard VGA cable, but it also provides a switch to toggle between RGB and VGA video modes (useful for monitors that accept both RGB and VGA frequencies), and a pixel clock signal to the Falcon030 video chip (to enable higher screen resolutions) compatible with the Blow-Up software.

The oscillator providing the pixel clock can be powered by the Falcon030 itself (by connecting the pin header of the adapter), or powered externally by the USB connector on the adapter. For standard screen resolutions, no power is needed.

The 3-in-1 monitor adapter comes with 2 oscillators (40MHz and 50MHz), a USB cable suitable for powering the oscillator by external means, the adapter itself, and printed instructions.

The adapter is now available in exxos store. Please note that although the adapter was originally designed by me, I have nothing to do with the 3-in-1 monitor adapters built and sold by exxos. Support for the adapters obtained from exxos store is provided by exxos. /Daniel

Release date:
May 31, 2017
Hardware requirements:
Atari Falcon030
VGA monitor

ACE Tracker v2.0
ACE TRACKER ACE is a complete 16-bit synthesizer for Atari Falcon030 compatible computers. It features one of the most advanced sound engines ever made for the Atari series of computers. ACE is the gathering title of two products, ACE MIDI and ACE Tracker. Both applications use the same sound engine which enables musicians from both worlds to exchange sounds and ideas even if the method of making music is completely different. There are some soft synthesizers already available for the Atari Falcon030, but none of these has the functionality of ACE, such as filters and MIDI support. ACE is aimed towards musicians whom want something completely new, easy to use, inspirational and fun to make music with.

This is the full version of ACE Tracker, a soundtracker based on the ACE engine. Version 2.0 is major update with many new features as well as quality enhancements. The user guide has been updated and is available in the Adobe PDF format and can be downloaded by clicking the link to the right. Some of the new features of version 2.0 are listed below.
  • Triangle wave and Trisaw wave
  • High-pass, band-pass and band-stop filters
  • Filter disable
  • Square transformator added to oscillator 1
  • Sawtooth sub-oscillators added to oscillators 1 and 2
  • Hard sync-mix mode
  • Reverb and delay can be disabled (or output 3/4) per patch
  • Two new source oscillators in FM-mix mode
  • Amplifier with or without limiting that can be used for distortion effects
  • Improved .WAV support
  • Increased maximum number of samples to 256
  • New tracker commands.

Release date:
June 27, 2014
Hardware requirements:
Atari Falcon030
4Mb ST-RAM
VGA or RGB monitor
File information:
ACETR200.ZIP
589 kb
Downloads: 1140
Total: 3173 (all versions)

MagiC Keyboard Patch v1.1
MagiC has a fixed keyboard configuration and if it does not match your actual keyboard, it may be hard to find out what key to press to get the character you want, or even worse, some letters of your spoken language may not be accessible by a single key press at all.

The Magic Keyboard Patch will update the MAGIC.RAM file with a new keyboard configuration. Currently two predefined configurations are included: Swedish and English (UK).

If none of the predefined keyboard configurations suits you, it is possible to create your own.

Version 1.1 fixes compatibility issues with older Atari computers and an incorrect key mapping in the CUSTOM.KBD file.

Release date:
December 10, 2013
Hardware requirements:
Atari ST/TT/Falcon030
512kb ST-RAM
VGA, RGB or mono. monitor
Software requirements:
MagiC (Atari version)
File information:
MKBDP11.ZIP
66 kb
Downloads: 241
Total: 248 (all versions)

Replace v0.37
Replace - ACE Tracker replay library. Use this replayer to play ACE Tracker modules (AM) in your own productions. Includes library, function defines and an example source in asm.

Release date:
September 7, 2005
Hardware requirements:
Atari Falcon030
4Mb ST-RAM
File information:
REPLV037.ZIP
186 kb
Downloads: 1278
Total: 1370 (all versions)

ACE MIDI v1.01 - demo version
ACE MIDI ACE is a complete 16-bit synthesizer for Atari Falcon030 compatible computers. It features one of the most advanced sound engines ever made for the Atari series of computers. ACE is the gathering title of two products, ACE MIDI and ACE Tracker. Both applications use the same sound engine which enables musicians from both worlds to exchange sounds and ideas even if the method of making music is completely different. There are some soft synthesizers already available for the Atari Falcon030, but none of these has the functionality of ACE, such as filters and MIDI support. ACE is aimed towards musicians whom want something completely new, easy to use, inspirational and fun to make music with.

ACE MIDI fits perfectly into any studio as it has a wide range of possibilities. Use the wave oscillators to create warm, cold, smooth, funny, weird, strange sounds, or load some samples to create that perfect beat. Everything is easily controlled by a number of devices. Use the LFO for vibrato, tremolo and wah-wah effects, the STEP MODULATOR on vocals to achieve "Cher singing" effects. All this in 16 bit resolution. Tap your sounds individualy through 4 outputs to your favourite effect box and add reverb, distortion or what ever you feel like, or use the internal effects to give your sounds that extra touch. The sounds in ACE MIDI ranges from retro chip-blip-blop sounds to multi-sampled pianos, strings or what ever you want to do. All this nicely packaged in a easy to use interface.

Please note that the demo version is restricted in many ways and that you need to register ACE MIDI to get the full version. Click here for registration details.

The latest full version of ACE MIDI is 2.0 (released in June, 2014) and is available to registered users only.

Release date:
March 15, 2002
Hardware requirements:
Atari Falcon030
4Mb ST-RAM
VGA or RGB monitor
File information:
AMDEMO01.ZIP
321 kb
Downloads: 1288

FlexTrax v0.9
FlexTrax Finally an update of the FlexTrax soundtracker for Atari Falcon030 compatible computers. FlexTrax features an user-friendly graphical interface in high resolution (640x480 pixels) with a built-in sound sample editor. Much have changed and many new functions are introduced in this new version of FlexTrax. Version 0.9 has support for both the AVR and WAV sample formats and the sample editor has been greatly improved. FlexTrax supports the standard MOD file format (up to eight channels) for compatibility reasons but also features a new enhanced module format FLX. The FLX format is an extended version of the standard MOD file format with support for real-time sound effects like reverb and delay. The replay routine used in FlexTrax was first developed for our platform game Willie's Adventures.

If you create a module that makes use of the real-time effects in FlexTrax, please send us a copy of it! Thank you!

Release date:
September 24, 2000
Hardware requirements:
Atari Falcon030
4Mb ST-RAM
VGA or RGB monitor
File information:
FTRAX09.ZIP
598 kb
Downloads: 1499

MagiC IDE Patch v2.2
A patch for MagiC (the multitasking operating system from Application Systems Heidelberg). The patch forces MagiC to skip the check for IDE hard drives on Atari Falcon030 compatible computers and Atari ST computers equipped with the H&N Multiboard. On systems not equipped with IDE hard drives this speeds up the boot-up sequence dramatically. Version 2.2 of the patch is compatible with MagiC 6 as well as all earlier versions of MagiC.
Release date:
March 20, 1999
Hardware requirements:
Atari ST/TT/Falcon030
512kb ST-RAM
VGA, RGB or mono. monitor
Software requirements:
MagiC (Atari version)
File information:
MPATCH22.ZIP
3 421 bytes
Downloads: 327

Flu - a 4kB intro
FLU This intro was supposed to be released at the "Alternative Party" 1998 held in Finland, but unfortunately it wasn't finished in time.
Release date:
November 3, 1998
Hardware requirements:
Atari Falcon030
4Mb ST-RAM
VGA or RGB monitor
FPU co-processor
File information:
FLU.LZH
7 964 bytes
Downloads: 208

Maggie 24 Intro
MAGGIE 24 INTRO The intro for the 24th issue of the Falcon030 version of Maggie, the diskmagazine from Reservoir Gods.
Release date:
October 14, 1997
Hardware requirements:
Atari Falcon030
4Mb ST-RAM
VGA or RGB monitor
File information:
M24INTRO.ZIP
202 kb
Downloads: 190

Blue - a 4kB intro
BLUE Blue was New Beat's contribution to the 4kB intro competition at the QuaST 1997 party in Poland.

It was voted second best intro in the competition.
Release date:
August 4, 1997
QuaST 1997
Hardware requirements:
Atari Falcon030
4Mb ST-RAM
RGB monitor
File information:
BLUE.ZIP
4 938 bytes
Downloads: 154

Willie's Adventures - 2nd preview
Willie's Adventures The second preview of the the platform game "Willie's Adventures" for Atari Falcon030 compatible computers. Now with even better graphics and sound, animated enemies, larger levels, parallax scrolling, improved animations, and much more!

Release date:
March 31, 1997
Hardware requirements:
Atari Falcon030
4Mb ST-RAM
VGA or RGB monitor
File information:
WP970331.ZIP
852 kb
Downloads: 843

RGB Reine
RGB REINE This demo was made for the demo competition at the Nordic Atari Show 1996 in Gothenburg, Sweden. It was never intended to be a serious contribution. It was done in a couple of hours and just for the fun of it. Enjoy!
Release date:
July 1, 1996
Hardware requirements:
Atari Falcon030
4Mb ST-RAM
RGB monitor
File information:
RGBREINE.ZIP
200 kb
Downloads: 131

Willie's Adventures - 1st preview
WILLIE'S ADVENTURES - FIRST PREVIEW The first preview of the platform game "Willie's Adventures" for Atari Falcon030 compatible computers. Featuring parallax scrolling with 64 foreground colours and four background colours, eight channel 8bit/50KHz sound, Jaguar Joypad support, VGA and RGB monitor support, and much more.

Release date:
February 4, 1996
Hardware requirements:
Atari Falcon030
4Mb ST-RAM
VGA or RGB monitor
File information:
WP960204.TOS
462 kb
Downloads: 182

RATSoft/ST Local Download Script v1.1a
This script is written in RAT-Script and is intended to be used with the RATSoft/ST BBS System. In RATSoft/ST local mode the script makes it possible to copy files marked for download to a specified path.
Release date:
November 20, 1995
Hardware requirements:
Atari ST/TT/Falcon030
4Mb ST-RAM
VGA, RGB or mono. monitor
Software requirements:
RatSoft/ST v2.1 (or higher)
File information:
LOCDL11A.LZH
6 435 bytes
Downloads: 229